Dies, Their Construction and Use for the Modern Working of Sheet Metals: A Treatise on the Design, Construction and Use of Dies, Punches, Tools, Fixtures and Devices, Together with the Manner in which They Should be Used in the Power PressN.W. Henley & Company, 1902 - 384 oldal |
Részletek a könyvből
1 - 5 találat összesen 40 találatból.
21. oldal
... brass rod about 21⁄2 inches long , and solder one end of it to the back of the templet as shown in Fig . 9. The templet is now complete and there is no possibility of getting the wrong side up . We now take a piece of soft sheet brass ...
... brass rod about 21⁄2 inches long , and solder one end of it to the back of the templet as shown in Fig . 9. The templet is now complete and there is no possibility of getting the wrong side up . We now take a piece of soft sheet brass ...
22. oldal
... brass rod , enter it into the die from the back , holding it as parallel as pos- sible with the face of the die . By holding a piece of white paper in front of the die it will be noticed that the die touches the templet at only a few ...
... brass rod , enter it into the die from the back , holding it as parallel as pos- sible with the face of the die . By holding a piece of white paper in front of the die it will be noticed that the die touches the templet at only a few ...
29. oldal
... brass , copper , zinc , silver , paper , leather , cloth , etc. In Figs . 12 and 15 , K is the punch holder or stem , I the punch plate , H the punch which is let into the punch plate and upset at the back , as shown . The punch plate ...
... brass , copper , zinc , silver , paper , leather , cloth , etc. In Figs . 12 and 15 , K is the punch holder or stem , I the punch plate , H the punch which is let into the punch plate and upset at the back , as shown . The punch plate ...
30. oldal
... brass , iron , etc. , a moderate amount of shear will give the best results , while for heavy stock a greater amount must be given . These dies are usually made PUNCH ONE PIECE PLAN OF DIE , SHOWING BEVELED EDGES WITH A NARROW MARGIN ...
... brass , iron , etc. , a moderate amount of shear will give the best results , while for heavy stock a greater amount must be given . These dies are usually made PUNCH ONE PIECE PLAN OF DIE , SHOWING BEVELED EDGES WITH A NARROW MARGIN ...
32. oldal
... brass and other heavy stock they harden both male and female dies , drawing the male somewhat lower than the female , and provide them with stripping plates and construct the dies somewhat dif- KEY PART OF HINGE SPECIAL BLANK CHAIN ...
... brass and other heavy stock they harden both male and female dies , drawing the male somewhat lower than the female , and provide them with stripping plates and construct the dies somewhat dif- KEY PART OF HINGE SPECIAL BLANK CHAIN ...
Más kiadások - Összes megtekintése
Dies, Their Construction and Use, for the Modern Working of Sheet Metals: A ... Joseph Vincent Woodworth Nincs elérhető előnézet - 2018 |
Dies, Their Construction and Use, for the Modern Working of Sheet Metals: A ... Joseph Vincent Woodworth Nincs elérhető előnézet - 2018 |
Gyakori szavak és kifejezések
accomplished adjustable allow annealed automatic bending and forming bending punch blank holder blanking die blanking punch bolster bottom brass BROOKLYN cast iron chuck clearance construction curling cutting edge dial feed diameter disks dowels drawing punch drilled E.W.BLISS embossing face finished fixtures flat forging gage plate groove hardened and drawn hardened and tempered heat heavy stock holes inside lathe centers located and fastened machine manner milled milling machine necessary perforating piece piercing punches pins Plan of Punch polished portion power press produced proper punch and die punch descends punch holder punch plate punch strikes radius reamed roll feed round screws seaming second operation sections shape shown sheared sheet metal sheet-metal shown in Fig side slide soft spring barrel spring pad stop-pin strip stripper plate stroke stud surface taper templet thickness of metal tion tool steel trimming tube wire
Népszerű szakaszok
372. oldal - Rule. — Multiply the diameter of the driver by its number of revolutions, and divide the product by the number of revolutions of the driven; the quotient will be its diameter.
3. oldal - Comprising fundamental designs and practical points by which sheet metal parts may be produced at the minimum of cost to the maximum of output, together with special reference to the hardening and tempering of press tools and to the classes of work which may be produced to the best advantage by the use of dies in the power press.